InsertCore

Technical Guides and Resources

Practical tooling knowledge from our engineers — insert grades, coatings, failure diagnosis, parameters and tool-life practice.

MAINTENANCE

Sep 22 · 9 min read

Cutting Fluid Problems: Corrosion, Smell, and the Fixes

Flash rust, rotten-egg smell, and short sump life trace to pH, concentration, chloride, and tramp oil. The two-number fix for cutting fluid problems.

Ray ChanRead Article
MAINTENANCE

Sep 22 · 8 min read

How to Extend Carbide Tool Life: 9 Proven Practices

Nine shop-tested practices that extend carbide tool life: wear limits, chip load, coolant discipline, runout, entry rules and regrind math, with numbers.

Ray ChanRead Article
DRILLING

Sep 22 · 10 min read

Cobalt vs HSS vs Carbide Drill Bits: What Actually Lasts Longer

Cobalt, HSS and carbide drill bits compared on red hardness, speed windows, tool life and cost per hole, with the rigidity rule that decides the winner.

Ray ChanRead Article
MILLING

Sep 22 · 11 min read

Climb Milling vs Conventional Milling: Direction Matters

Climb vs conventional milling decided by physics: chip thickness, force direction, scale, backlash. The rules, and when each one wins.

Ray ChanRead Article
MILLING

Sep 22 · 10 min read

2 Flute vs 4 Flute End Mills: Which One for Your Job?

2 flute vs 4 flute end mill decided with real chip load math: slotting, aluminum, steel, stainless, finishing and deep pockets, plus a side-by-side table.

Ray ChanRead Article
MATERIAL GUIDES

Sep 22 · 9 min read

Why Does Aluminum Stick to End Mills? Built-Up Edge Explained

Built-up edge in aluminum explained: the weld-and-tear cycle, the stickiest alloys, and the geometry, flute, coating and parameter fixes that stop it.

Ray ChanRead Article
TROUBLESHOOTING

Sep 22 · 14 min read

Why Do Carbide End Mills Break? A Prevention Checklist

Why carbide end mills break: the three failure modes, chip thinning math, coolant and holder rules, and a startup checklist that stops the next fracture.

Ray ChanRead Article
TROUBLESHOOTING

Sep 22 · 10 min read

Why Do Carbide End Mills Chatter? 7 Causes and Fixes

Chatter fixes for carbide end mills: seven causes from overhang to speed regime, the wave-on-wave mechanism, and a cheapest-first diagnostic sequence.

Ray ChanRead Article
TURNING INSERTS

Sep 22 · 11 min read

Carbide Insert Selection Guide: ISO Grades & Chipbreakers Explained

Decode CNMG 120408 digit by digit, match ISO 513 groups to grades and chipbreakers, and run vendor-published speed and feed windows for steel and cast iron.

Ray ChanRead Article
THREADING

Sep 22 · 11 min read

Tap Drill Size Chart: How to Pick the Right Drill Bit (UNC/UNF/Metric)

How to pick tap drill sizes from published ANSI and ISO charts. The 75% thread rule, the metric formula, material adjustments and worked examples.

Ray ChanRead Article
MATERIAL GUIDES

Sep 22 · 14 min read

How to Choose End Mill Coatings: TiAlN vs AlTiN vs Uncoated

How to choose end mill coatings by wear mechanism. Published TiAlN and AlTiN temperature bands, when bare carbide wins, and what the datasheet must show.

Ray ChanRead Article
MATERIAL GUIDES

Sep 22 · 13 min read

How to Choose Carbide End Mills by Workpiece Material

End mill selection by workpiece material: ISO 513 grade groups, coatings, flutes, helix, edge prep and published starting speeds for steel, stainless, cast iron, aluminum, titanium and hardened steel, with source rows.

Ray ChanRead Article